Influence of thickness and initial groove angle in M–K model on limit strain of 7B04 by considering through-thickness stress

Marciniack–Kuczinski (M–K) model is widely used to predict material’s forming limit curve (FLC). The prediction of FLC traditionally neglected through-thickness normal stress. However, it cannot be neglected in some forming processes. Much work has been done to study the effect of through-thickness normal stress on FLC with constant through-thickness normal stress or constant ratio of through-thickness normal stress and maximum principal stress. In addition, based on Nakazima test process, the ratio of through-thickness normal stress and maximum principal stress has been derived, which was a function of instantaneous thickness and loading path. Here, initial groove angle in M–K model was not considered. In this paper, uniaxial tension tests and Nakazima tests were performed on 7B04 aluminum alloy. Based on Hill 48 yield criterion and M–K model, the prediction model of FLC was established. The increase of thickness can enhance FLC. Meanwhile, it is necessary to consider through-thickness normal stress and initial groove angle in prediction model. On the left side of FLC, the effect of initial groove angle on FLC is weakened by increasing sheet thickness. On the right side of FLC, the effect of initial groove angle on FLC is strengthened by increasing sheet thickness. On the right side of FLC, the relation between limit strain points with different thicknesses is linear under one certain loading path. Thickness has decisive effect on through-thickness normal stress level and the changing trendy of through-thickness normal stress during calculation is different under different stress condition.     

细晶铸造K418B合金热处理工艺研究

研究了不同热处理工艺与 K41 8B合金细晶铸件组织和性能的关系 ,结果表明 ,合金组织中的γ′相大小和晶界上次生碳化物的形态和分布对中温持久性能具有重要影响。提出了 K41 8Β合金细晶铸件合适的真空热处理制度为 :1 1 80℃ / 2 h,AC 93 0℃ / 1 6h,AC     

小鹰-500飞机疲劳试验载荷谱的编制方法

针对小鹰500飞机的设计和使用特点，选用了FAA推荐的通用飞机实测载荷谱数据，按照民机的TWIST编谱原则编制出用重心过载表示的“飞-续-飞”随机疲劳试验载荷谱，用于小鹰-500飞机机翼疲劳试验，并参照国外文献中有关尾翼载荷谱的保守处理方法，采用了从重心载荷谱计算出配套平衡的平尾机动载荷，将其幅值放大1.2倍和频次放大3倍的做法，编制出了平尾疲劳试验载荷谱。     

New multifrequency measurements of the spectrum of the cosmic background radiation

New measurements of the Cosmic Background Radiation temperature at 12 cm, 6.3 cm, 3 cm, 0.9 cm and 0.3 cm have made in July 1982 from the White Mountain High Altitude Research Station. The results are presented and the existence of spectral distortions discussed.     

高温合金K38G微晶涂层氧化动力学研究

研究了溅射微晶涂层对K38G在800℃和900℃空气中氧化动力学的影响。发现微晶化后K38G的氧化动力学与经典的抛物线规律存在负偏差。分析认为,微晶化后氧化物形核率大大提高,氧化膜中的扩散由晶格扩散变为晶界短路扩散为主,从而改变了氧化膜的生长动力学。根据Wagner高温氧化的基本理论,对微晶合金高温氧化动力学规律进行了探讨,导出微晶K38G合金氧化动力学遵循四次方规律,即x4=kPt。     

对K8飞机外贸出口工作的几点思考

简要论述了K8飞机外贸出口所处的内、外部环境,在此基础上进行SWOT分析,并据此提出该飞机外贸出口工作中应采取的几项措施。     

基于FPGA的RS232转429接口电路的设计与实现

介绍用于自动控制设备控制板卡的软硬件设计方法,采用混合输入（包括SCH和VHDL）实现该设计,重点阐述应用ISP开发软件采用VHDL语言实现整个软件接收、控制部分,测试表明设计方法合理有效。     

超声横波斜探头K值对缺陷定位的影响

本文重点分析了影响横波斜探头K值测量的因素之一的测试用横孔埋深,对实测K值的影响,通过实验,得出了两个修订方程,可以提高横波斜探头在探伤时对缺陷的定位精度。     

空间微小碎片累积作用下材料光学性能退化预示模型适用性研究

航天器在轨服役期间会遭受到大量空间微小碎片和微流星体的撞击作用,其中的微米级粒子将在航天器表面产生大面积砂蚀现象,并使材料或器件功能衰退。文章介绍了NASA空间微小碎片累积损伤材料光学性能退化预示模型并推导了两个预示模型之间的关系。利用ORDEM2000碎片分布模型估算了K8玻璃累积损伤面积。以K8玻璃为例,对比研究了两个预示模型的适用性。结果表明,当航天器外表面损伤程度小于40%,可利用Canoon模型评价和预示材料光学性能退化规律;当航天器外表面损伤程度大于40%,需利用Mirtich模型评价和预示材料光学性能退化规律。     

H型球粒陨石TL灵敏度与冲击相和钾含量的研究

测定了坠落在我国武安、枣阳、信阳等地的10个H型球粒陨石的热释光(TL)灵敏度、自然热释光峰温和峰半高宽温度,同时对它们的K含量进行了测定.将测得的H型球粒陨石的TL灵敏度与它们的钾含量和所属冲击相进行比较.结果表明,H型球粒陨石的TL灵敏度与其钾含量和冲击相之间存在着规律性的关系.